(FOR MODELS MANUFACTURED SINCE 9/11)
-8-Model W1829 (Mfg. Since 9/11)
-9-Model W1829 (Mfg. Since 9/11)This machine must be connected to the correct size and type of power supply ci
-10-Model W1829 (Mfg. Since 9/11)This machine MUST be grounded. In the event of certain types of malfunctions or break
-11-Model W1829 (Mfg. Since 9/11) This machine has been carefully packaged for
-12-Model W1829 (Mfg. Since 9/11) Refer to the Machine Specifications, on Page 3, for the weight and footprint specifications o
-13-Model W1829 (Mfg. Since 9/11)The strongest bench mounting option is a "Through Mount" where holes are drilled all the way through t
-14-Model W1829 (Mfg. Since 9/11) DISCONNECT JOINTER FROM POWER! Use two of the included M8
-15-Model W1829 (Mfg. Since 9/11). Sliding the fence bracket onto the fence support dovetails.Fence Support DovetailFence Bracket Assemb
-16-Model W1829 (Mfg. Since 9/11)The W1829 has a built-in dust collection fan and chip exhaust. It also includes a 2.5" dust port, clamp, an
-17-Model W1829 (Mfg. Since 9/11)1. TurnthemachinepowerswitchOFF.2. Insert the power cord plug into a matchingpowe
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, r
-18-Model W1829 (Mfg. Since 9/11)Once the assembly is complete, test run your machine to make sure it runs properly and is ready for regular oper
-19-Model W1829 (Mfg. Since 9/11)This machine will perform many types of operations that are beyond the scope of this manua
-20-Model W1829 (Mfg. Since 9/11)•
-21-Model W1829 (Mfg. Since 9/11)
-22-Model W1829 (Mfg. Since 9/11)The purpose of surface planing on the jointer is to make one flat face on a piece of stock (
-23-Model W1829 (Mfg. Since 9/11)The purpose of edge jointing is to produce a finished, flat-edged surface that is suitable for
-24-Model W1829 (Mfg. Since 9/11)The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see
-25-Model W1829 (Mfg. Since 9/11)The following jointer accessories may be available through your local Woodstock International In
-26-Model W1829 (Mfg. Since 9/11)D2675—Safety GlassesD2676—Adjustable Safety GlassesExceeding ANSI Z87.1–1989 standards for impact resistanc
-27-Model W1829 (Mfg. Since 9/11)Since all bearings are sealed and permanently lubricated, simply leave them alone un
-28-Model W1829 (Mfg. Since 9/11)This section covers the most common service adjustments or procedures that may need to be made during t
-29-Model W1829 (Mfg. Since 9/11) Machine has vibration or noisy operation
-30-Model W1829 (Mfg. Since 9/11)StraightedgeOutfeed Infeed Illustration of a typical cutterhead alignment setup. Hex
-31-Model W1829 (Mfg. Since 9/11) Move the straightedge to position A, as shown in Figure 39. Turn the jack screw nearest the
-32-Model W1829 (Mfg. Since 9/11) Hex Wrench 4mm ...1Hex Wrench 5mm ...
-33-Model W1829 (Mfg. Since 9/11)
-34-Model W1829 (Mfg. Since 9/11). Checking the inward 45º stop.. Adjusting the inward stop bolt. D
-35-Model W1829 (Mfg. Since 9/11) DISCONNECT JOINTER FROM POWER! Loosen the fence tilting handle, remove the limi
-36-Model W1829 (Mfg. Since 9/11)The Model W1829 uses two belts to drive the cutterhead and the dust collection impeller. Whe
-37-Model W1829 (Mfg. Since 9/11)This jointer has a universal motor that uses carbon brushes, which are considered wear-
-2-Model W1829 (Mfg. Since 9/11)This machine has been specially designed to provide many years of trouble-free
-38-Model W1829 (Mfg. Since 9/11)These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to t
-39-Model W1829 (Mfg. Since 9/11)PADDLE SWITCH(viewed from behind)Ground GroundNeutralHotGround110 VAC5-15 Plug(As Recommended)ReadPage 38Be
-40-Model W1829 (Mfg. Since 9/11)122A34556789101112131415161718192021222323-12424-124-224-324-4252627282929-1303133343536373940414243444
-41-Model W1829 (Mfg. Since 9/11)REF PART # DESCRIPTION REF PART # DESCRIPTION1 X1829001 TABLE 49 X1829049 ALIGNMENT PIN2 X1829002 FENC
-42-Model W1829 (Mfg. Since 9/11)
-43-Model W1829 (Mfg. Since 9/11)
-44-Model W1829 (Mfg. Since 9/11)TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWoodstock international inc. p
Model W1829 (Mfg. Since 9/11)WARRANTYWoodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and material
High Quality Machines and ToolsWoodstock International, Inc. carries thousands of products designed to meet the needs of today's woodworkers and
-3-Model W1829 (Mfg. Since 9/11)Model W1829 Machine Specifications, Page 1 of 2MODEL W1829SHOP FOX® 6" BENCHTOP JOINTERMotorsMainTyp
-4-Model W1829 (Mfg. Since 9/11)Model W1829 Machine Specifications, Page 2 of 2Table InformationTable Length...
-5-Model W1829 (Mfg. Since 9/11)Outfeed TableInfeed TableFenceCutterhead GuardON/OFF SwitchDepth of CutAdjusting KnobDu
-6-Model W1829 (Mfg. Since 9/11)Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury.Indica
-7-Model W1829 (Mfg. Since 9/11)APPROVED OPERATION. Untrained operators can be seriously hurt by machinery. Only allow trained or properly super
Comments to this Manuals