Woodstock SHOP FOX W1680 Owner's Manual

Model W1680***IMPORTANT UPDATE***Applies to Owner's ManualPrinted July, 2000 Phone #: (360) 734-3482 • Tech Support: [email protected] • W

-8-Figure 6. Components laid out for identification.The following is a description of the components shipped with the Shop Fox®W1680 Drill Press. It i

-9-While the main components of the Shop Fox®W1680 Drill Press are assembled at the factory, someassembly is required. The following is the recommende

-10-Figure 11. Correct rack orientation.Figure 9. Insert the pinion gear from the inside.Figure 10. Align setscrew with flat on pinion.Table Support1.

-11-Figure 12. Bottom of rack in position.Figure 13. Inside bevel in the correct position.Table Support, Cont.4. Slide the table support bracket onto

Head Stock1. The bottom of the headstock has a pocketfor inserting the column. An assistant willbe needed to position the pocket over thecolumn, as in

Figure 16. Tighten setscrews to secure headstock.Figure 17. Installing handles.Figure 17b. Installing a light bulb.HandlesThree handles are supplied w

-14-Drill Chuck and ArborFigure 19. Seating the arbor into chuck.Figure 18. Chuck components identification.The drill chuck is attached to the drill s

Figure 20. Seating arbor into spindle.-15-A wedge is included with the Shop Fox®DrillPress which aids in drill chuck arbor removal.1. Rotate the spind

-16-Speed ChangeADJUSTMENTSUnplug the drill press before changing speeds.The Drill Press has 12 speeds ranging from 140to 3050 RPM. There is a speed c

-17-More About Speed ChangesSpindle AdjustmentsYour new drill press comes fitted with a depth stop for use when drilling. Follow the instruc-

INSTRUCTION MANUALMODEL W168017" DRILL PRESSPhone: 1-800-840-8420 • On-Line Technical Support: [email protected] © 2000 BY

-18-Table AdjustmentsThe table can be adjusted for height, rotationand angle. Follow these instructions to adjustheight:1. Loosen the support bracket

-19-OPERATIONSOnce assembly is complete and adjustments aredone to your satisfaction, you are ready to testrun the machine.Make sure the starting swit

-20-Care must be taken to secure the bit firmly inplace. When changing bits, proceed as follows:1. Disconnect the machine from the powersource.2. Open

-21-MAINTENANCELubricationSince all bearings are shielded and permanentlylubricated, simply leave them alone until theyneed to be replaced. Do not lub

-22-The following pages contain general machinedata, parts diagrams/lists and warranty/returninformation for your Shop Fox®Model W1680 17"Drill

Table Of ContentsPAGE1. INTRODUCTION ...2ABOUT YOUR NEW DRILL PRESS ...

-2-INTRODUCTIONABOUT YOUR NEW DRILL PRESSThis new Shop Fox®Drill Press has been specially designed by Woodstock International, Inc. to providemany yea

-3-WARRANTY AND RETURNSWoodstock International, Inc. warrants all SHOP FOX®machinery to be free of defects from workman-ship and materials for a perio

-4-READ MANUAL BEFORE OPERATING MACHINEFAILURE TO FOLLOW INSTRUCTIONS BELOW WILLRESULT IN PERSONAL INJURYSAFETY FIRST!1. Thoroughly read the instructi

1. Always operate your drill press at speeds that are appropriate for the drill bit size and the mate-rial that you are drilling.2. Feed the drill bit

-6-This equipment must be grounded. Verifythat any existing electrical outlet and circuityou intend to plug into is actually grounded.If it is not, it

-7-AVOIDING POTENTIAL INJURIESFigure 2. Never drill, holding workpiece by hand.Figure 3. Keep fingers away from spinning tool.Fig. 4. Remove Switch Sa