Woodstock SHOP FOX W1668 Instruction Manual

INSTRUCTION MANUALMODEL W1668131⁄4" Oscillating Drill PressPhone: 1-800-840-8420 • On-Line Technical Support: [email protected]

-9-ASSEMBLYWhile the main components of the Shop Fox®W1668 Oscillating Drill Press are assembled at the factory,some assembly is required. The followi

-10-Figure 11.Lock shoe Inserted into table bracket.Figure 9. Insert the pinion gear from the inside.Figure 10. Align setscrew with flat on pinion.Tab

-11-Figure 12. Hold rack in position while installing.Figure 13. Inside bevel in the correct position.Figure 14. Lock shoe in place and secured.Table

-12-HeadStock1. The bottom of the headstock has a pocketfor inserting the column. Position the pock-et over the column, as in Figure 15. Allowthe head

-13-HandlesThree handles are supplied with your newOscillating Drill Press. Thread them into the hubas in Figure 20.Figure 20. Spindle handle installa

-14-Speed ChangeADJUSTMENTSUnplug the drill press before changing speeds.The Oscillating Drill Press has 12 speeds rangingfrom 250 to 3050 RPM. There

-15-Spindle AdjustmentsYour new drill press comes fitted with a depthstop for use when drilling. Follow the instruc-tions below for use.1. Loosen the

-16-Oscillating FeatureOne of the great features of the W1668 DrillPress is its capability for oscillating sanding. Thedrill press can be converted fr

-17-Table AdjustmentsThe table can be adjusted to accommodateheight of materials to be sanded or drilled. Toadjust:1. Loosen the table support bracke

Always wear safety glass-es when operating drillpress. Failure to complymay result in serious per-sonal injury.-18-OPERATIONSOnce assembly is complete

-1-Table Of ContentsPAGE1. INTRODUCTIONABOUT YOUR NEW DRILL PRESS ...2WOODSTOCK SERVICE AND SUPPORT

Installing the sanding drum spindle is identical to installing a drill bit. However, it is important to installthe paper and drum before installing th

-20-MAINTENANCELubricationSince all bearings are shielded and permanentlylubricated, simply leave them alone until theyneed to be replaced. Do not lub

-21-The following pages contain general machinedata, parts diagrams/lists and warranty/returninformation for your Shop Fox®Model W1668Drill Press.If

PARTS

-23-55 XPB07M HEX BOLT M8-1.25 X 2556 XPB09M HEX BOLT M8-1.25 X 2057 X1668057 PUSH ROD58 X1668058 SPRING59 X1668059 RUBBER WASHER60 X1668060 OSCILLATI

-24-NOTES:

CUT ALONG DOTTED LINE10. What stationary woodworking tools do you own? Check all that apply.___Air Compressor ___Panel Saw___Band Saw ___Planer___Dril

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWOODSTOCK INTERNATIONAL, INC.P.O. BOX 2309BELLINGHAM, WA 98227-2309

-2-INTRODUCTIONABOUT YOUR NEW DRILL PRESSThis new Shop Fox®Oscillating Drill Press has been specially designed by WoodstockInternational, Inc. to prov

-3-WARRANTY AND RETURNSWoodstock International, Inc. warrants all SHOP FOX®machinery to be free of defects from workman-ship and materials for a perio

-4-READ MANUAL BEFORE OPERATING MACHINEFAILURE TO FOLLOW INSTRUCTIONS BELOW WILLRESULT IN PERSONAL INJURYSAFETY FIRST!1. Thoroughly read the instructi

1. Always operate your drill press at speeds that are appropriate for the drill bit size and the mate-rial that you are drilling.2. Feed the drill bit

-6-110V OperationELECTRICAL REQUIREMENTSWhen it is necessary to use an extension cord,use the following guidelines:•Use cords rated for Hard Service•N

AVOIDING POTENTIAL INJURIES-7-Figure 2. Never drill, holding workpiece by hand.Figure 3. Keep fingers away from spinning tool.Fig. 4. Remove Switch Sa

-8-Figure 6. Components laid out for identification.The following is a description of the components shipped with the Shop Fox®W1668 Oscillating Drill