Woodstock SHOP FOX M1106 Specifications Page 80
- Page / 100
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
-78-
Model W1811 (For Machines Mfd. Since 6/14)
SERVICE
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Machine has vibration or
noisy operation.
1. Motor or component is loose.
2. Blade is at fault.
3. Belt(s) worn or loose.
4. Pulley is loose.
5. Motor mount loose/broken.
6. Machine is incorrectly mounted or
sits unevenly.
7. Arbor pulley is loose.
8. Motor fan is rubbing on fan cover.
9. Arbor bearings are at fault.
10. Motor bearings are at fault.
1. Inspect/replace stripped or damaged bolts/nuts,
and re-tighten with thread locking fluid.
2. Replace warped, bent, or twisted blade; resharpen
dull blade.
3. Inspect/replace belts (refer to Page 68).
4. Realign/replace shaft, pulley, setscrew, and key as
required.
5. Tighten/replace.
6. Tighten/replace anchor studs in floor; relocate/shim
machine.
7. Retighten/replace arbor pulley with shaft and thread
locking liquid.
8. Replace dented fan cover; replace loose/damaged
fan.
9. Replace arbor housing bearings; replace arbor.
10. Test by rotating shaft; rotational grinding/loose
shaft requires bearing replacement.
Operation
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Workpiece has burned
edges, binds, or kicks
back.
1. Sliding table is not parallel to
blade.
2. Splitter/riving knife is not aligned
with the blade.
3. Blade is warped.
1. Make sliding table parallel to the
blade (Page 70).
2. Shim the splitter/riving knife to align it with the
main blade.
3. Replace the blade.
Workpiece has chip out on
the bottom edge.
1. Scoring blade height is incorrect.
2. Scoring blade is not aligned with
the main blade.
3. Scoring blade kerf does not match
the main blade.
1. Adjust the height of the scoring blade.
2. Align the scoring blade (Page 42).
3. Adjust the scoring blade kerf (Page 42).
Sliding table saw does not
cut square.
1. Sliding table is not parallel to
blade.
2. Rip fence is not parallel to blade.
3. Crosscut fence is not perpendicular
to the blade.
1. Adjust the sliding table (Page 70).
2. Adjust the rip fence parallel to blade.
3. Adjust the crosscut fence perpendicular to the blade
(Page 72).
Fence hits table top when
sliding across table.
1. Front rail is too low.
2. Rip fence roller is too low.
1. Raise the front rail.
2. Adjust the rip fence roller.
Blade does not reach 90˚,
or blade does not reach
4 5˚.
2. Blade stop bolts are out of adjust-
ment.
2. Adjust the stop bolts (Page 69).
The rip fence scale is not
accurate.
1. The rip fence scale is out of calibra-
tion or was not set up correctly.
1. Adjust the rip fence scale.
Handwheels for blade
adjustments will not turn
or are difficult to turn.
1. Shipping braces still attached.
2. Lock knob is tight.
3. Gears caked with dust.
1. Remove shipping braces.
2. Release the lock knob.
3. Clean out dust and grease the gears.
Motor & Electrical Ctd.
- OWNER'S MANUAL 1
- Contents 3
- INTRODUCTION 4
- Controls & Features 5
- MODEL W1811 6
- SLIDING TABLE 9
- SAW CAPACITIES 9
- For Your Own Safety 10
- Preventing Kickback 13
- Protecting Yourself 13
- From Kickback 13
- Glossary Of Terms 14
- ELECTRICAL 15
- Grounding Requirements 16
- Extension Cords 16
- Unpacking 17
- Items Needed for Setup 17
- Inventory 18
- Cleaning Machine 20
- Machine Placement 20
- Lifting & Moving 21
- Assembly & Setup 22
- 8" 24
- ...to T-bolt 26
- M8-1.25 x 55 26
- Flat Washer 26
- 8" or 3mm hex 29
- Dust Collection 31
- Test Run 32
- OPERATIONS 34
- 4" 35
- Non-Through & Through 36
- Splitter/Riving Knife 37
- Safety Tips 40
- Blade Size Requirements 41
- Blade Selection 41
- Dado Blades 42
- Changing Main Blade 43
- Changing/Adjusting 44
- Scoring Blade 44
- Rip Cutting 45
- Rip Cutting with Rip Fence 46
- Crosscutting 47
- Crosscutting Full Size Panels 48
- Crosscutting Smaller Panels 48
- Miter Cutting 49
- Dado Cutting 50
- Dado Blade 51
- Workpiece 51
- Rabbet Cutting 53
- Resawing 55
- Auxiliary Fence 56
- Resawing Operation 57
- MAINTENANCE 58
- SHOP-MADE SAFETY ACCESSORIES 59
- Featherboard 61
- Push Sticks 62
- Push Blocks 63
- Zero-Clearance Insert 64
- 32" Hole 65
- Outfeed & Support Tables 66
- Crosscut Sled 66
- ACCESSORIES 67
- Lubrication 69
- 2" or 70
- Blade Tilt Calibration 71
- Sliding Table Parallelism 72
- Sliding Table Adjustment 73
- Calibrating Crosscut 74
- Fence 90° Stops 74
- Mounting Block 75
- WIRING DIAGRAM COLOR KEY 76
- Wiring Diagram 77
- Electrical Pictures 78
- Troubleshooting 79
- Operation 80
- Motor & Electrical Ctd 80
- Labels & Cosmetics 81
- Trunnion 83
- Main Motor 84
- Sliding Table 86
- Sliding Table Parts List 87
- Rip Fence 89
- Handwheels 90
- Scoring Trunnion 91
- Crosscut Table 92
- Swing Arm 93
- Miter Gauge 94
- Crosscut Fence 95
- CUT ALONG DOTTED LINE 97
- FOLD ALONG DOTTED LINE 98
- WARRANTY 99
Related products and manuals for Circular saws Woodstock SHOP FOX M1106
(8 pages)
Circular saws Woodstock W1099 Specifications
(21 pages)
(21 pages)
Circular saws Woodstock M1013 User Manual
(48 pages)
(48 pages)
Circular saws Woodstock M1113 User Manual
(60 pages)
(60 pages)
Circular saws Woodstock W1824 User Manual
(88 pages)
(88 pages)
© 2020, manymanuals.com. All rights reserved. | 0.223 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals