Woodstock SHOP FOX W1667 Instruction Manual

INSTRUCTION MANUALMODEL W166781⁄2" Oscillating Drill PressPhone: 1-360-734-3482 • On-Line Technical Support: [email protected]

-8-Figure 6. Components laid out for identification.UNPLUG machine beforeany assembly procedures.Otherwise serious personalinjury may occur!WEAR safet

-9-To install the base and column, do thesesteps:1. Position the drill press base on a flat andstable surface.2. Using two clamps, clamp the base to t

Figure 9. Loosely installing table lock lever.To install the table, do these steps:1. Thread the table lock handle 3 turns intothe table support brack

-11-Figure 10. Aligning the pocket in the headstockwith the column.Figure 11. Securing the headstock to the column.Set screwsHeadstockTo install the h

-12-Three handles are supplied for drilling opera-tions. NOTE: remove these handles when youuse the oscillating feature. To install the handles, do t

-13-The drill press drive belt lasts a long time;however, during its life the belt may stretchslightly, which can cause the pulleys to slipunder a loa

-14-Figure 20. Typical spring cover lock slot andlocking lug.Spring-CoverLock SlotLocking LugFigure 18. Feed shaft return spring assembly.Figure 19. Q

While you may never have to adjust the quill-shaft screw, you should understand its functionand know how to adjust it should you everneed to remove th

-16-To adjust the table, do these steps:1. Hold onto the table with one hand andloosen the table lock knob. See Figure 24.2. Lift or lower the table

-17-To change the drilling speed, do these steps:1. UNPLUG THE DRILL PRESS!2. Refer to the speed chart located under thebelt cover or refer to the “D

WARNINGSome dust created by power sanding, sawing, grind-ing, drilling, and other construction activities con-tains chemicals known to the State of Ca

Use Figure 30 to select the optimum motor-to-spindle pulley ratio for drilling, cutting, and sandingoperations. Refer to the Drill, Cutter, and Saw R

-19- ADJUSTMENTS

-20-ADJUSTMENTS

-21-Once assembly is complete and adjustmentsare done to your satisfaction, you are ready tostart the drill press. Every time you start thedrill press

-22-To change drill bits and sanding drums, dothese steps:1. UNPLUG THE DRILL PRESS!2. Use the chuck key to open the chuck wideenough to accept the ne

-23-One of the great features of the Model W1667 8 1⁄2'' Oscillating Drill Press is its sanding capa-bility. The drill press can be converte

7. Choose the insert that has an openingwhich is slightly bigger than the sandingdrum chosen. See Figure 39.8. Insert the sanding drum mandrel into th

-25-Since all bearings are shielded and permanentlylubricated, simply leave them alone until theyneed to be replaced. Do not lubricate them.For other

-26- Use this table to isolate and correct any problems with your drill press. If you cannot correct a problem,contact Woodstock International, Inc. a

-27-Parts DiagramMAINTENANCE

-1-ELECTRICAL ADJUSTMENTSOPERATIONSMAINTENANCEASSEMBLYSAFETYINTRODUCTIONCONTENTSINTRODUCTION ...

-28-REF PART # DESCRIPTION46 XP6203 BALL BEARING 620347 X1667047 QUILL ASSEMBLY (48-54)48 XPR48 EXT RETAINING RING 11MM49 X1667049 COLLAR50 XP6201 BAL

SHOP FOX®Drill Press Vises use precision ground steel guide rods,smooth-action Acme threads, ground steel jaws, with fixed jaw V-grooves for holding r

-30-Steelex®Carded Forstner Bitsstack up as some of the best bits in theworld. In fact, an independent testing lab proved that the Steelex®brand cut w

CUT ALONG DOTTED LINE10. What stationary woodworking tools do you own? Check all that apply.___Air Compressor ___Panel Saw___Band Saw ___Planer___Dril

TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWOODSTOCK INTERNATIONAL, INC.P.O. BOX 2309BELLINGHAM, WA 98227-2309

-2-This new SHOP FOX®Model W1667 8 1⁄2'' Oscillating Drill Press has been specially designed byWoodstock International, Inc. to provide many

-3-Woodstock International, Inc. warrants all SHOP FOX®machinery to be free of defects from work-manship and materials for a period of 2 years from th

Standard Safety Instructions-4-READ MANUAL BEFORE OPERATING MACHINEFAILURE TO FOLLOW INSTRUCTIONS BELOW WILLRESULT IN PERSONAL INJURY1. Thoroughly rea

1. Always operate your drill press at speeds that are appropriate for the drill bit size and thematerial that you are drilling.2. Feed the drill bit e

Figure 1. Never drill while holding the workpiece by hand.Figure 2. Keep fingers away from spinning drillbits, cutters, and sanding surfaces.Figure 3.

-7-Figure 5a. Never remove grounding pin.Figure 5. Model W1667 wiring diagram.Ground this machine! The electrical cord sup-plied with the W1667 8 1⁄2&