Model W1701 ¾ HP SHAPERMANUAL UPDATECOPYRIGHT © FEBRUARY, 2008 BY WOODSTOCK INTERNATIONAL, INC.WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN
-7-W1701 1HP ShaperELECTRICALELECTRICAL110V OperationWhen it is necessary to use an extension cord, use the following guidelines:• Use cords rated fo
-8-W1701 1HP ShaperSET UPThe SHOP FOX® Model W1701 has been carefully pack-aged for safe transporting. If you notice the machine has been damaged, ple
-9-W1701 1HP ShaperSET UP• Machine Mobility: Use the Model D2057 SHOP FOX® Heavy-Duty Mobile Base so you can make the most out of your shop space by
-10-W1701 1HP ShaperSET UPAssemblyFigure 9. Attaching cross bars to stand side.Figure 10. Attaching stand to shaper unit.To assemble the shaper, do th
-11-W1701 1HP ShaperSET UP8. For custom fence facing, make sure the screw heads are countersunk completely below the surface of the fence face.9. Co
-12-W1701 1HP ShaperOPERATIONSOPERATIONSGeneralDO NOT investigate problems or adjust the Machine Name while it is running. Wait until the machine is t
-13-W1701 1HP ShaperOPERATIONSSpindle ElevationFigure 15. Spindle lock knob.Figure 16. Spindle-height lever.Correct spindle height is crucial to most
-14-W1701 1HP ShaperOPERATIONSThe two fence faces are independently adjustable to allow for different shaping tasks. The fence faces can be set at dif
-15-W1701 1HP ShaperOPERATIONSCutter InstallationBefore installing cutters, you must plan the configuration of rub collars and cutters required for th
-16-W1701 1HP ShaperOPERATIONSTo install cutters and rub collars, do these steps:1. DISCONNECT SHAPER FROM POWER SOURCE!2. Slide the cutter(s) and r
OWNER'S MANUALMODEL W1701 1 HP SHAPERPhone: (360) 734-3482 • E-Mail: [email protected] © AUGUST, 2003 BY WOODSTOCK INTERNATIONA
-17-W1701 1HP ShaperOPERATIONSBefore using router bits, you should convert the shaper to a router table. Refer to Table Spacer Kit on Page 23 to learn
-18-W1701 1HP ShaperOPERATIONSBecause the shaper fence is independently adjustable, you can set up the shaper to cut part or all of the workpiece edg
-19-W1701 1HP ShaperOPERATIONS5. Now place a straightedge against both faces of the fence to check alignment. Once they are both in alignment, make s
-20-W1701 1HP ShaperOPERATIONSFreehand shaping is shaping without the aid of the miter slot or fence. The most dangerous part of shaping free-hand is
-21-W1701 1HP ShaperMAINTENANCEMAINTENANCERegular periodic maintenance on your Model W1701 1HP Shaper will ensure its optimum performance. Make a habi
-22-W1701 1HP ShaperSERVICESERVICEThis section covers the most common service adjustments or procedures that may need to be made during the life of yo
-23-W1701 1HP ShaperSERVICEThe provided table spacer kit allows you to modify your shaper for use as a router table by raising the table. A higher tab
-24-W1701 1HP ShaperSERVICEShould a bearing fail, your shaper will probably develop a noticeable rumble, which will increase when the machine is put u
-25-W1701 1HP ShaperSERVICEThe fence can be resurfaced or made flat with a jointer to correct any warping. This procedure should only be done if the f
-26-W1701 1HP ShaperSERVICEElectrical Components & Wiring
-27-W1701 1HP ShaperPARTS
-28-W1701 1HP ShaperPARTSParts ListREF PART�# DESCRIPTION REF PART�# DESCRIPTION301 X1701301 SIDE�PANEL 351 X1701351 KNOB�FEMALE�M6-1.0302 X1701302 TI
-29-W1701 1HP ShaperPARTSREF PART�# DESCRIPTION REF PART�# DESCRIPTION400 X1701400 RUB�COLLAR�1/2"�X�13/16"�X�3/8" 431 XPSS01M SET�SCRE
WarrantyWoodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work-manship and materials for a period of two years
W1701 1HP ShaperCUT ALONG DOTTED LINEName ___________________________________________________________________________________Street __________________
TAPE ALONG EDGES--PLEASE DO NOT STAPLEFOLD ALONG DOTTED LINEFOLD ALONG DOTTED LINEWOODSTOCK INTERNATIONAL INC. P.O. BOX 2309 BELLINGHAM, WA 98227-2309
SET UPELECTRICALMAINTENANCESERVICEPARTSOPERATIONSSAFETYINTRODUCTIONUSE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!ContentsINTRODUCTION
-2-W1701 1HP ShaperINTRODUCTIONWoodstock Technical SupportWe stand behind our machines! In the event that questions arise about your machine, parts ar
-3-W1701 1HP ShaperSAFETYSAFETYREAD MANUAL BEFORE OPERATING MACHINE.FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL RESULT IN PERSONAL INJURY.Standard Safet
-4-W1701 1HP ShaperSAFETY10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to a complete stop before leaving
-5-W1701 1HP ShaperSAFETYAdditional Safety Instructions for Shapers1. KEEPING HANDS SAFE: Never pass your hands near or directly over or in front of
-6-W1701 1HP ShaperSAFETYAvoiding Potential InjuriesFigure 1. Use a SHOP FOX® Featherboard as anti-kick back protection.Figure 2. Use rubberized SHOP
Comments to this Manuals